Codekit foundation error software#
Codekit foundation error code#

However, after some investigation under a microscope and with a multimeter testing continuity, I found no hardware issues anywhere on the board and moved onto software troubleshooting. Originally my fear was a short somewhere on the board, connecting the button terminals.

Codekit foundation error code#

Luckily enough, this upload worked the first time, however upon uploading the code, the LED on my board remained on at all times no matter the state of the button, unlike the intention of my code to turn the LED on when the board’s button was pressed.

I uploaded this code from the Arduino IDE through my in-circuit programmer board to my button blinky board using the IDE’s Upload Using Programmer feature. With this code flushed out, I attached my newly made button blinky board to my UPDI in-circuit programmer I worked on in week 4’s electronics production class and then connected my programmer to my laptop through the programmers FTDI headers. Due to the addressing of this pin as an input, the theory of this code is that the 412 chip will be confused by this request, and infer that that high value should run to the pin’s pull-up resistor, thus turning it on. The process of turning on such resistor involved writing a high value to digital pin one. During this board testing, I wrote a simple Arduino sketch that blinks a LED at the press of the board’s button, attached below.Īddressing pin 1 as my board’s button input pin, and activating the ATTiny 412 chips internal pull-up resistor. Arduino IDE ¶Ĭonveniently enough, I had coded my Button Blinky board in the Arduino IDE before this week, while testing the board after manufacturing it in my week 6 assignment. With the schematic-based circuit all wired up and connected to a power supply, I used the drag block interface inside for Tinker Circuits to read the chips button pin and turn on an LED when the button was closed or switched on. During this process, I had to keep in mind the microcontroller being used, as although my original board schematic called for an ATtiny 412 microcontroller, Tinker Circuits only has an ATtiny 45 in its inventory, and thus I had to reference a pinout (shown below) of the ATtiny 45 while creating the circuit. I attached all these parts to a breadboard and connected the circuit to a power supply. I began this process by first building the circuit in the Tinker Curcits environment, basing the design on my button blinky board schematic. This read-through gave me useful information on the microcontroller to keep in mind while coding, such as the pinout of the chip, and peripheral registers, which came in handy while programming the chip with port manipulation in C.ĪTtiny 412 Microcontroller Pinout in Data Sheetĭescription of the ATtiny 412 Microcontoller's I/O Pins Tinker Circuits ¶Īs a first step into the Embedded Programming week, after completing the datasheet reading, I used Autodesk’s Tinker Circuits to simulate a model of my board made on virtual breadboard components. (Mar 17)īefore starting any programming of my button blink board, I skimmed through the 500-page datasheet for the Attiny 412 microcontroller.

Throughout the week I used the Arduino IDE, VSC with PlatformIO, Code Kit as environments, where I programmed my button blink board in C with Arduino Libraries, C++, Block-Based Code, and also simulated the board with Tinker Circuits. This week I read the datasheet for the ATtiny 412 microcontroller and then used information from the sheet to program my button blink board made in week 6’s electronic design class, in as many different programming languages and environments as possible. Invention, Intellectual property & Income Principles and Practices & Project Managementġ8. So in googling around trying to see if there was a way to tell wordpress to look into the /css folder and look for a file called site.css I found this code I can add to my functions.php file.1. It has to go into a folder of some sort relative to the root folder, like a /css folder. It requires that all files have a specific output path, in other words I can't specify that the style.scss file should compile to a style.css file in the root directory. I'm using codekit to compile my themes sass files and minify my scripts as well. I haven't done wordpress development in quite some time so it looks like some things have changed (naturally).